than five additional full width cross
grating for maintenance of fittings and
members on shall be provided in the area
other equipment shall be furnished. The
of the rear bogie. The additional cross
deck plate shall be free of ragged or sharp
members may be joined by welding to the
exposed edges.
normally located cross members in the
3.5.2.6
HOSE TENDER.
rear bogie area. Crossmembers shall be
When a tilt cab is furnished, a pogo stick
of full channel construction, or equal, with
type hose tender shall be provided behind
a minimum RBM of 55,000 in. / lb.
the cab to accommodate and secure the
reinforced by gusset plates or brackets at
semitrailer lighting cable and air hoses. A
points of attachment to longitudinal sills,
pogo stick shall be provided on all types
and
contact
edges
of
welded
of cabs and mounted rearward when a
reinforcements shall be welded for not
rear mounted spare carrier or a rear-
less than 50 percent of the edge length.
mounted winch is furnished. When a
Longitudinal sills shall be constructed of
conventional cab is furnished without a
structural steel channels or formed
rear mounted spare carrier and without a
channels. Formed channel sills shall be
rear mounted winch, a cab mounted
reinforced within the sill, at each
tender as specified in 3.4.2.5 may be
crossmember or body mounting point,
provided in lieu of a pogo stick. Hose
with formed channel reinforcements.
tender shall conform to TMC RP 417.
Figure 5
FRAMING
STANDARD EQUIVALENT EQUIVALENT
3.5.3
TYPE III (STAKE).
MEMBER
GAGE NO. MILLIMETER
INCHES
Type III stakes shall have body
Cross-member
10
3.416
0.1345
dimensions as specified per the Standard
Side and end
rails
10
3.416
0.1345
Item Number, or optional body length per
Longitudinal
option code. A rear bumper shall be
sills
8
4.176
0.1644
furnished. Stake racks and platform body
Reinforcement
8
4.176
0.1644
shall be painted black.
Rack post
11
3.038
0.1196
Wiring harness across the rear apron
3.5.3.1
STAKE BODY.
shall be enclosed in conduit or
The body shall consist of a steel frame
polyethylene loom except at terminal ends
platform, wood floor, and side and end
and shall be secured by rubber insulated
racks. When a hydraulic crane, option
metal cable clamps to the under body
code SAC, is furnished, the body shall be
structure on not more than 12 inch
mounted to provide a space back of cab-
centers.
to-body of not less than 810 mm (32
inches) for mounting the crane.
3.5.3.3
STAKE BODY FLOORING.
The platform shall be floored with wood,
3.5.3.2
STAKE BODY FRAME.
or when specified, with steel. Wood parts
Body framing shall be completely welded
shall be treated in accordance with
structure with members of minimum gage
3.1.1.3.
thickness specified in Figure 5 for carbon
steel; high tensile steel may be furnished
3.5.3.4
STAKE BODY WOOD FLOORS.
in two gages lighter weight in accordance
Wood floors shall be apitong, hardwood or
with
US
Standard
gage
sizes.
pressure treated dense southern yellow
Crossmembers shall have no more than
pine not less than 33 mm (1-5/16 in) thick
40 cm (16 inch) center spacing, including
(finished dimension) Plywood type floors
ends and stub crossmembers as required
shall not be acceptable. Wood floors shall
for proper spacing over axle. Not less
Federal Standard 807M
Page 24 of 65
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business